Foam Board Insulation in South Ogden that stops the drafts
Foam Board Insulation in South Ogden is the fastest way to stop cold air from pouring through your attic, basement, or crawl space. We install rigid foam insulation panels in South Ogden homes built from the 1950s through the 2000s, where thin walls and settled batts leave gaps you can feel. If your furnace runs nonstop in January and your upstairs never warms up, the problem is usually missing or compressed board insulation. We fix that in a single visit.
Service overview
What Foam Board Insulation in South Ogden actually does
Foam Board Insulation in South Ogden is a rigid panel product, usually polyiso or extruded polystyrene, cut to fit between studs, joists, and rim boards. Unlike fiberglass batts that rely on trapped air, foam board panels hold a fixed R-value per inch and do not sag, settle, or soak up moisture. We cut each panel with an insulation saw, seal the edges with air sealing caulk gun beads, and tape the seams so the wall behaves like one continuous thermal barrier. Most homes need 1 to 2 inches of board on basement walls and 2 inches in attics. South Ogden sits in a cold, dry pocket of Weber County where winter nights drop below 20 degrees and summer afternoons push past 95. That swing punishes cheap insulation. Homes near Burch Creek and the Ogden River Bottoms deal with extra moisture, which is why we pair rigid foam insulation panels South Ogden with a proper vapor barrier. If you have been searching for foam board insulation South Ogden UT cost, the honest answer is that board costs more per square foot than blown-in cellulose, but it lasts decades longer in a wet crawl space.
! Problems we solve
Drafty rooms and cold floors all winter
Your furnace runs longer, your gas bill climbs, and the rooms above the garage or crawl space never feel warm no matter what you set the thermostat to.
Ice dams forming on the roof every February
Heat escaping into the attic melts snow that refreezes at the eaves. Water backs up under the shingles, rots the deck, and stains the ceiling inside.
Wet, musty crawl space with sagging insulation
Fiberglass batts soak up groundwater, lose their R-value, and hold moisture against the framing. That leads to rot, mold, and poor indoor air quality upstairs.
Scope of work
What our foam board insulation service includes
Every foam board job includes the diagnostic visit, the board itself, air sealing, and cleanup. What changes from home to home is thickness, square footage, and whether a vapor barrier or thermal barrier is required by code. We spell out exactly what is covered in the written scope before we start.
-
01
Thermal and moisture inspection
We scan your walls, attic, and crawl space with a thermal imaging camera and check for moisture with a meter. You see the cold spots on screen and get a written scope the same day. This step tells us whether board is the right fix or whether air sealing alone will do it.
-
02
Rigid foam board panels
We supply and install Owens Corning, Johns Manville, or CertainTeed board in the thickness your walls need, typically 1 to 2 inches. Panels are cut to fit each bay within a quarter inch and fastened with cap nails or a staple gun. No gaps at the corners.
-
03
Air sealing and vapor barrier
Before the board goes up, we seal rim joists, top plates, and penetrations with Great Stuff foam and air sealing caulk gun beads. In basements and crawl spaces we add a vapor barrier on the warm side. This is the step that turns a stack of panels into a real thermal envelope.
-
04
Cleanup and verification
After installation we re-scan the walls to confirm the temperature difference is gone, then sweep and haul out every scrap of board and foam. You get a short walkthrough of what we did and what to watch for next winter. Most jobs are done in one day.
Why South Ogden homeowners choose foam board
Foam board insulation does three jobs at once: it blocks heat transfer, stops air leaks, and resists moisture. Here is what that means for your house in real numbers.
Book a walkthroughTools and methods we use
Thermal imaging camera
We use it before and after every job to find cold spots and confirm the board actually fixed them. You see the before-and-after images yourself, not just a verbal report.
Moisture meter
Checks framing and concrete for hidden moisture before we cover anything with board. Installing foam over a wet wall traps the problem and causes rot, so this step is non-negotiable.
Insulation saw and utility knife
Cuts polyiso and XPS board to fit each bay within a quarter inch. Clean cuts mean tight seams, and tight seams are where the R-value actually comes from.
Air sealing caulk gun and Great Stuff foam
Seals rim joists, top plates, and penetrations before the board goes up. Air sealing is the cheapest energy upgrade in any home, and it makes the board work better.
Local execution
South Ogden sits at the mouth of Weber Canyon, which means cold air drains down off the mountains at night and sits in the lower neighborhoods. Winter lows regularly hit the teens, and summer afternoons push past 95. That swing is hard on insulation, and it is why foam board outperforms batts here. The housing stock runs from 1940s bungalows near Downtown South Ogden to 1990s builds in Shadow Valley, and most of them were framed with 2x4 walls that never had a thermal break. We see the same three problems over and over: bare rim joists in basements, settled batts in attics, and wet crawl spaces near the Ogden River Bottoms. If you have been pricing foam board insulation South Ogden UT cost, remember that board costs more upfront but does not sag or soak up water, so it lasts decades longer in our climate. We pull permits where required and install to current Utah code.
How foam board insulation runs in South Ogden
- • Downtown South Ogden
- • Burch Creek
- • Shadow Valley
- • Country Hills
Recent work
Same-week scheduling across South Ogden
When your wall is open, we move fast
Most foam board insulation jobs in South Ogden get scheduled within two business days of your call, and we can often walk your home the same week. Our trucks carry 1-inch and 2-inch Owens Corning and Johns Manville board, Great Stuff foam, vapor barrier, and air sealing caulk, so a standard basement or attic job does not wait on a supply run. Each crew runs two to three technicians depending on access, and a typical 1,000-square-foot basement takes 6 to 10 hours. If a pipe bursts in January and your wall is open, call (855) 927-7517 and we will get board back in place so the rest of the house stays warm. We serve 84405, 84403, and the surrounding Weber County area.
How our foam board installation works
Walkthrough and moisture check
We start with a thermal imaging camera and a moisture meter, walking your attic, basement, and crawl space. You get a written scope the same day showing where heat is escaping and whether any wet framing needs to dry first. This visit takes 45 to 60 minutes.
Measure and cut panels
We measure each bay and cut Owens Corning or Johns Manville foam board panels to fit within a quarter inch. Panels go in tight, with no gaps at the corners. Cutting happens outside or in the garage so your living space stays clean.
Air seal and set board
Before the board goes up, we seal penetrations, rim joists, and top plates with Great Stuff foam and air sealing caulk gun beads. Then we set each panel, fasten it with a staple gun or cap nails, and tape the seams. This is the step that actually stops the drafts.
What foam board insulation costs
Foam board insulation in South Ogden runs $1,200 to $4,500 for most homes in 2026, depending on square footage, board thickness, and how much prep work the space needs. A single crawl space with 1-inch board is at the low end. A full basement plus rim joist with 2-inch polyiso is at the high end. We quote a fixed price after the walkthrough, so you know the number before we start. Board costs more per square foot than blown-in cellulose, but it does not settle or soak up water, which is why it lasts decades longer in our climate.
Square footage and thickness
A 500-square-foot crawl space with 1-inch board is a much smaller job than a 1,200-square-foot basement with 2-inch polyiso. Thickness drives both material cost and labor, since thicker board takes longer to cut and fit tightly.
Access and prep work
A clean, empty basement goes fast. A crawl space with 18 inches of clearance, or a wall that needs old wet batts removed first, adds hours. We include removal and disposal in the quote when it is needed.
Vapor barrier and thermal barrier
Basements and crawl spaces need a vapor barrier on the warm side, and living spaces need a code-required thermal barrier over the foam. Both add material and labor, but skipping them causes moisture problems or a failed inspection.
Foam board insulation questions
How much does foam board insulation cost in South Ogden UT?
Most South Ogden foam board jobs run $1,200 to $4,500 in 2026, depending on square footage and thickness. A single crawl space with 1-inch board starts near $1,200. A full basement plus rim joist with 2-inch polyiso lands closer to $4,000. Attic-only retrofits are usually the cheapest because access is easier. We quote a fixed price after the walkthrough.
What is the best rigid foam insulation for Utah?
Closed-cell polyiso gives the highest R-value per inch, about R-6.5, and handles Utah's temperature swings without losing performance. Extruded polystyrene is the better pick for below-grade basement walls because it resists moisture. We stock Owens Corning, Johns Manville, and CertainTeed board and match the product to the location. Attics get polyiso; basements and crawl spaces get XPS.
Is foam board insulation good for basements in South Ogden?
Yes, and it is usually the best option for a South Ogden basement. Board goes directly against the concrete, adds R-5 to R-13 depending on thickness, and does not soak up groundwater the way fiberglass batts do. We pair it with a vapor barrier and air sealing at the rim joist. That combination keeps the space dry and stops the cold floor feeling upstairs.
Who installs foam board insulation near South Ogden?
Coolshift Assembly installs foam board insulation across South Ogden, Weber County, and the surrounding 84403 and 84405 ZIP codes. We handle cutting, air sealing, vapor barrier, and code-required thermal barriers in one visit. Call (855) 927-7517 and we will schedule a walkthrough, usually within two business days.
Related services
Spray Foam Insulation
Spray polyurethane foam fills the odd-shaped gaps that board cannot reach, like rim joists and penetrations. We often combine spray foam at the rim with board on the flat walls for a tighter envelope in South Ogden homes.
Attic Insulation
Board on the attic floor plus blown-in cellulose on top gives you the highest R-value per dollar. If your South Ogden attic has bare joists or settled batts, this pairing is the fastest way to cut winter heat loss.
Get Foam Board Insulation in South Ogden this week
Cold floors and drafty rooms do not fix themselves, and every winter you wait costs you another season of high gas bills. We are a licensed, insured local crew with board on the truck. Call (855) 927-7517 or request a walkthrough and we will show you exactly where your home is losing heat.